Measurement-computing TempScan/1100 Bedienungsanleitung Seite 21
- Seite / 306
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
TempScan / MultiScan User’s Manual 899493 System Overview 1-7
Calibration
Calibration of cold junction sensor: Software control of calibrated thermocouple using ChartView’s
built-in calibration feature. The automated calibration function is accessed from ChartView’ Device
pull-down menu using “Select Status” and then selecting “Calibration.” Note that calibration is
performed for each card and chassis in the system.
Voltage Calibration: Software control of gain and offset.
Calibration Constants: Chassis constants stored in NV-RAM. Card constants stored in card’s on-board
EEPROM.
Hardware Configuration
The TempScan/1100 or MultiScan/1200 unit is equipped with a high-speed IEEE 488 interface and an
RS-232 interface. Its IEEE 488 interface is useful in laboratory applications and enables real-time transfers
of acquired data to the host computer’s hard drive for inexpensive mass storage.
Its RS-232 interface is ideal in applications that require the placement of instrumentation at remote
distances from the controlling computer, such as process and environmental control.
This unit can be set up with an IEEE 488 or a RS-232 interface configuration, as determined by the DIP
switch accessible from the rear panel. This DIP switch via its nine microswitches select which command
set is to be used – IEEE 488 or RS-232 – and the operating parameters for each.
The table shows the options for its nine microswitches. Additional DIP switch settings are shown in the
following sections.
Rear Panel DIP Switch
Micro- Label Setting Description
switch #
IEEE 488 RS-232
1
COMM SELECT 0 IEEE 488 (N/A)
1 (N/A) RS-232
2,3
HANDSHAKE (H/S) 00 No Handshake No Handshake
01 Software Handshake only
(XON/XOFF) (See Note)
Software Handshake only
(XON/XOFF) (See Note)
10 Hardware Handshake only
(RTS/CTS)
Hardware Handshake only
(RTS/CTS)
11
Both Hardware and Software
Handshake
Both Hardware and Software
Handshake
4,5
IEEE ADDRESS or 00 Decimal value 0 No Parity
PARITY 01 Decimal value 8 Odd Parity
10 Decimal value 16 Even Parity
11 Decimal value 24 (N/A)
6,7,8
IEEE ADDRESS or 000 Decimal value 0 300 baud
BAUD RATE 001 Decimal value 1 600 baud
010 Decimal value 2 1200 baud
011 Decimal value 3 2400 baud
100 Decimal value 4 4800 baud
101 Decimal value 5 9600 baud (See Note)
110 Decimal value 6 (N/A)
111 Decimal value 7 (N/A)
9
CHASSIS 0 Disabled Disabled
CALIBRATION
ENABLE
1 Enabled Enabled
Note:
(1) XON/XOFF handshaking is valid for ASCII transmissions only. (2) At 9600 baud,
hardware (RTS/CTS) handshaking and possibly software (XON/XOFF) handshaking may be
required to maintain serial performance.
- TempScan/1100 1
- MultiScan/1200 1
- Manual Layout 5
- Table of Contents 7
- 5 – System Operation 8
- 6 – System Calibration 8
- Quick Start Guide 11
- CAUTION 12
- Software Setup & Startup 13
- 988892 446-0940, rev 2.2 14
- System Overview 1 15
- Front Panel Indicators 16
- 899493 System Overview 1-3 17
- WARNING 20
- Hardware Configuration 21
- IEEE 488 Configuration 22
- 899493 System Overview 1-11 25
- Digital I/O Configuration 27
- Line Voltage Selection 32
- Fuse Replacement 34
- Rack Mount 35
- Bench Top 35
- Power-Up Activation 36
- Expansion Units 2 37
- 2-2 Expansion Units 38
- Expansion Unit 2-3 39
- Master/Slave Connection 40
- CAUTIONCAUTION 40
- Slave Configuration 41
- Channel Assignment 41
- Exp/11A Expansion Unit 43
- 2-8 Expansion Units 44
- Expansion Unit 2-9 45
- 2-12 Expansion Units 48
- Scanning Cards 3 49
- 3-2 Scanning Cards 50
- Scanning Cards 3-3 51
- 3-4 Scanning Cards 52
- 3-6 Scanning Cards 54
- MultiScan Scanning Cards 55
- 3-8 Scanning Cards 56
- Scanning Cards 3-9 57
- 3-10 Scanning Cards 58
- System Configuration 4 59
- Memory Allocation 60
- Required Configuration 64
- Scan Configuration 67
- 00:00:00.0 68
- I? command 68
- Acquisition Configuration 71
- Trigger Configuration 74
- Additional Configuration 76
- Alarm Configuration 77
- Stamp Configuration 80
- (2) PRINT#1, “OUTPUT07;R3X” 81
- (3) PRINT#1, “ENTER07" 81
- (4) INPUT A$ 81
- Data Format Configuration 84
- Power-Up Configuration 90
- System Operation 5 91
- Buffer Organization 92
- Trigger Block Configurations 93
- Buffer Query Operation 94
- Buffer Read Operations 95
- Buffer Overrun 101
- F) command 103
- Access to the HLL Registers 104
- 5-18 System Operation 108
- Theory of Operation 109
- Status-Reporting Registers 109
- 5-20 System Operation 110
- System Operation 5-21 111
- 5-22 System Operation 112
- Mask Registers 113
- Additional Operation 115
- Real-Time Clock 116
- System Calibration 6 117
- Calibration Setup 118
- Calibration Status 119
- Calibration Password 119
- K12345 120
- Software 131
- C3523DFA6C0A 133
- Overview 134
- 1) Waiting for Trigger 135
- Main Window 136
- 988992 ChartView , CV-5 137
- Channel Information Region 138
- Status Indicator Region 139
- Chart Pop-up Menu 140
- 988992 ChartView , CV-9 141
- CV-10 ChartView 142
- Software Reference 142
- Main Window Toolbar 143
- Display 144
- Configuration 144
- 988992 ChartView , CV-13 145
- CV-14 ChartView 146
- 988992 ChartView , CV-15 147
- 988992 Software Reference 148
- 988992 ChartView , CV-17 149
- Channel Configuration 150
- View File Data 150
- 988992 ChartView , CV-19 151
- Main Window Pull-Down Menus 152
- 988992 ChartView , CV-21 153
- View (continued) 155
- Acquire 156
- 988992 ChartView , CV-25 157
- Device … Interface ¾ 158
- 988992 ChartView , CV-27 159
- Device … Status ¾ 161
- 988992 ChartView , CV-31 163
- Bar Graph Meters 164
- Analog Meters 165
- Digital Meters 166
- Meter Toolbars 167
- Meter Pull-Down Menus 167
- Meters Configuration Menu 168
- Configuring a Meter 168
- Setup Window 169
- 988992 ChartView , CV-39 171
- CV-40 ChartView 172
- Acquisition Setup Dialog Box 173
- Acquisition Setup 174
- 988992 ChartView , CV-43 175
- CV-44 ChartView 176
- 988992 ChartView , CV-45 177
- Data Destination Dialog Box 178
- 988992 ChartView , CV-47 179
- Chart Setup Wizard 180
- 988992 ChartView , CV-49 181
- CV-50 ChartView 182
- ViewXL 183
- 989092 Software Reference 184
- Toolbar 185
- Load Configuration 186
- Options 186
- Data Acquisition Server 186
- Timestamps 187
- Multiple Data Files 188
- Import Files 188
- 457-0913 rev 3.0 189
- An Example Macro 191
- Sub GetData() 192
- ViewXL API Definition 193
- APPENDICES 195
- Introduction …… A-2 197
- Command Reference …… A-11 197
- Introduction 198
- Command Interpretation 199
- Immediate Immediate 200
- Immediate Immediate 200
- Command Summary 202
- Command Reference 207
- - Trigger On Command 208
- TempScan/1100 only 212
- - Reset Power-On 215
- - Configure Channels 221
- - Select Card 224
- - Set Relay Make Time 225
- MultiScan/1200 only 225
- - End Calibration Mode 226
- - Query Error Status 227
- - Set Data Format 228
- - Set Scan Interval 233
- - Set Trigger Level 237
- - Set Scan Rate 238
- - Set SRQ Mask 239
- - Set Measuring Mode 240
- - Set Event Mask 241
- - Set Digital Outputs 242
- - Program Trigger Times 243
- - Set Query Terminator 244
- - Query Card Data 245
- - Read Buffered Data 246
- - Read Last Readings 247
- - Set Real-Time Clock 248
- - User Status 251
- - Set User Terminator 254
- - Set Averaging Weight 255
- - Execute 256
- - Set Counts 257
- - Query 258
- IEEE 488 Bus Commands 260
- ASCII Codes 261
- ASCII Code Details 263
- Abbreviations 268
- Reading HLL Status 273
- (50) …… 15-WEND 278
- Operating Alarms 285
Verwandte Produkte und Handbücher für Hardware Measurement-computing TempScan/1100
(40 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern