Measurement-computing LogBook Series Bedienungsanleitung Seite 125
- Seite / 222
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
LogBook User’s Manual 949297 CE Compliance 8-3
Emissions/Immunity Conditions
The specific immunity conditions for CE compliance vary by product; but general immunity conditions
include:
• Cables must be shielded, braid-type with metal-shelled connectors. Input terminal connections are
to be made with shielded wire. The shield should be connected to the chassis ground with the
hardware provided.
• The host computer must be properly grounded.
• In low-level analog applications, some inaccuracy is to be expected when I/O leads are exposed to
RF fields or transients over 3 or 10 V/m as noted on the Declaration of Conformity.
CE Enhancements for Existing Products
This section describes three CE enhancements.
• DBK41/CE
• Edge Guards for the DBK5, DBK8, and DBK44
• BNC Connectors for CE compliance
Edge Guards for DBK5, DBK8, and DBK44
A plastic barrier attached to the end of a DBK card helps prevent access to leads, and to live circuits.
The edge guards attach to DBKs (see figure below) that are mounted in a DBK41/CE, with EMI shield
plates. The access slot allows insulated wires to pass through the barrier.
DBK41/CE
The DBK41/CE includes 3 variations of EMI shield plates that attach to the DBK41 enclosure. Besides
acting as an electrical safety barrier, these shields reduce electromagnetic interference (EMI).
Note: The CE kit is included with the DBK41/CE. It can be purchased as an optional accessory for use
with DBK41.
- LogBook/300 & /360 1
- Manual Layout 5
- Table of Contents 7
- Device Menu…… LV-48 9
- Tools Menu…… LV-51 9
- Indicators Menu…… LV-55 9
- LogBook Basics 11
- Front and Rear Panels 12
- Highlight of Features 13
- LogBook/300 Block Diagram 14
- LogBook/360 Block Diagram 15
- Operational Features 18
- Communications 20
- Triggering and Scan Timing 21
- Scan Rate Limitations 21
- Acquisition 23
- Data Storage and Retrieval 23
- General 25
- A/D Specifications 25
- Analog Inputs 25
- Triggering 25
- High-Speed Digital I/O 26
- Frequency/Pulse Counter 26
- Frequency/Pulse Generator 26
- Sequencer 26
- General Purpose Digital I/O 26
- Before you get started 27
- QS300-3 28
- CAUTION 29
- Hardware Configuration 29
- QS300-5 30
- Testing the Hardware 32
- A Note about Calibration 33
- Software Installation 34
- WARNING 35
- Setting Up the Card Drawer 36
- QS360-5 38
- Card Drawer Setup 39
- System Expansion 4 45
- What are DBK Options? 46
- ED7B55484273 47
- Considerations 48
- Mechanical Setup Options 49
- P1 – Analog I/O 51
- P2 Digital I/O 52
- DBK Basics 55
- Introduction 55
- /100 /200 Series 56
- 967794 DBK Basics, pg. 3 57
- 967794 Daq Systems 58
- DBK Identification Tables 63
- Analog Signal Conditioning 64
- 967794 DBK Basics, pg. 11 65
- Power Supply DBKs 66
- 967794 DBK Basics, pg. 13 67
- (see Notes 1 and 2) 68
- On a DBK34 and DBK34A 68
- 967794 DBK Basics, pg. 15 69
- Power Requirements 70
- DaqBook/2000 Series Devices 71
- Power Requirements Table 71
- 967794 DBK Basics, pg. 19 73
- This table is continued 74
- Additional Reading 75
- LBK/COM/422/485 78
- Hardware Description 80
- LBK1 Installation 81
- Remote LogBook Terminal 82
- Main Menu 82
- ***** 82
- LBK1 Menu Map 83
- LBK1 - Specifications 84
- LBK2 - Specifications 86
- Serial Input Fundamentals 90
- Capabilities and Limitations 90
- Installation and Setup 91
- Configuring an Acquisition 92
- Configuration Setup Overview 93
- Format String Reference 96
- Channel Type Selection Table 98
- GPS Examples 98
- LogBook/GPS - Specifications 101
- What is a Modem? 103
- Step X.2 – Set up the Modem 106
- Step Y.2 – Set up the Modem 114
- Frequently Asked Questions 120
- Overview 123
- CE Standards and Directives 123
- CE Compliance 8 123
- Safety Conditions 124
- DBK41/CE 125
- ED7B55484273 127
- Understanding LogView 127
- Modes of LogView Operation 128
- 989592 LogView LV-3 129
- 989592 Software Reference 130
- Software User-Interface 131
- 989592 LogView LV-7 133
- File Management 134
- 989592 LogView LV-9 135
- Procedures 137
- Using an Attached LogBook 138
- 989592 LogView LV-13 139
- Using LogBook “Unattached” 140
- Simple Data Logging 140
- 989592 LogView LV-15 141
- Setting Up DBK Cards 142
- Using Multiple Timebases 143
- 989592 LogView LV-19 145
- 989592 LogView LV-21 147
- Using Exception Capturing 149
- Menu Descriptions 150
- File Menu 150
- Save As 151
- Download 153
- Configuration Report 153
- ED7B55484273 154
- View Menu 155
- 989592 LogView LV-31 157
- 989592 LogView LV-33 159
- 989592 LogView LV-35 161
- 989592 LogView LV-37 163
- ~ AND-expression 165
- & 10010000 = = 10010000 165
- Example 1: P1_CH14 > 23 166
- Example 3: P1_CH14+P1_CH15 167
- Example 4: P1_CH14*2 167
- Acquisition Configuration 168
- 989592 LogView LV-43 169
- Preferences 171
- Device Menu 173
- LogBook Monitor 174
- Explorer 175
- Tools Menu 176
- 989592 LogView LV-51 177
- Merging Binary Data 178
- View Data 179
- Indicators Menu 180
- Digital 181
- Meters Configuration 181
- Enable Input Reading Column 183
- Appendix A A 185
- 1 = “Base” unit 192
- 0 = “Remote” unit (default) 192
- Set for 115200 192
- Error Codes 195
- Hardware Errors 196
- 878394 DD-1 197
- 878394 Dimensional Drawings 198
- 878394 DD-3 199
- 878394 DD-5 201
- 878394 DD-7 203
- 878394 DD-9 205
- DBK200 Series Boards 206
- 878394 DD-11 207
- 878394 DD-13 209
- 878394 DD-15 211
- 878394 DD-17 213
- POD-1 (for DBK83) 215
- 878394 DD-21 217
- Glossary 219
- 887199 Glossary xiii 221
Verwandte Produkte und Handbücher für Hardware Measurement-computing LogBook Series
(91 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.037 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern