Measurement-computing CIO-EXP-GP Bedienungsanleitung Seite 4
- Seite / 46
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
38
9.2 Reference Material for Application of Strain Gauges
.........................
38
9.1.2 Specification of Strain Gauges
...........................................
38
9.1.1 What Are Strain Gauges?
...............................................
38
9.1 About Strain Gauges
......................................................
38
9 APPENDIX
....................................................................
36
8 SPECIFICATIONS
............................................................
35
7.9 Verifying the Installation
...................................................
32
7.8.3 Strain Gauge Bridge Configuration Examples
.............................
32
7.8.2 Nulling Potentiometers & Arm Resistor
..................................
31
7.8.1 Bridge Completion Resistors
............................................
30
7.8 Configuring the Bridge
....................................................
30
7.7 Setting the Input Configuration
.............................................
29
7.6.2 Setting the Channel Gain
...............................................
29
7.6.1 Setting the Board Gain
.................................................
28
7.6 Setting the Gain
...........................................................
28
7.5 Determining the Appropriate Gain
..........................................
28
7.4.3 Selecting the Excitation Voltage
.........................................
26
7.4.2 Selecting the Power Source for the Excitation Voltage
......................
26
7.4.1 Selecting the Power Source for the Board
.................................
26
7.4 Powering the CIO-EXP-GP
................................................
26
7.3 CJC Jumper Select
........................................................
26
7.2 VEXC Jumper Select
......................................................
26
7.1 Channel Select
............................................................
26
7 CONFIGURATION FOR RESISTANCE MEASUREMENTS
.....................
25
6.9 Verifying the Installation
...................................................
24
6.8.3 Four-Wire RTD Hookup
................................................
24
6.8.2 Three-Wire RTD Hookup
...............................................
24
6.8.1 Two-Wire RTD Hookup
................................................
24
6.8 Connecting RTDs To Screw Terminals
......................................
23
6.7.1 Setting the Input Configuration
..........................................
23
6.7 Input Configuration
.......................................................
23
6.6.2 Setting the Channel Gain
...............................................
22
6.6.1 Setting the Board Gain
.................................................
22
6.6 Setting the Gain
...........................................................
20
6.5 Determining the Appropriate Gain
..........................................
20
6.4 Powering the CIO-EXP-GP
................................................
20
6.3 CJC Jumper Selection
.....................................................
20
6.2 VEXC Jumper Select
......................................................
20
6.1 Channel Selection
.........................................................
20
6 CONFIGURATION FOR RTD MEASUREMENTS
...............................
19
5.6 Verifying the Installation
...................................................
18
5.5.2 Setting the Channel Gain
...............................................
18
5.5.1 Setting the Board Gain
.................................................
18
5.5 Setting the Gain
...........................................................
- CIO-EXP-GP 1
- User’s Manual 1
- HM CIO-EXP-GP.lwp 2
- Table of Contents 3
- 1 INTRODUCTION 5
- 2 SOFTWARE INSTALLATION 5
- 3 GENERAL CONFIGURATION 6
- 3.3 Configuring the A/D Board 7
- 3.3.1 DAS08 Family Setup 7
- 3.3.2 DAS16 Family Setup 7
- 3.3.3 All A/D Boards 7
- 3.4.3 Other A/D Boards 8
- 3.5 Powering The CIO-EXP-GP 9
- 3.5.1 Power Source Switch 9
- 4.1 Channel Selection 12
- 4.2 Powering the CIO-EXP-GP 12
- 4.4 Setting the Gain 13
- 4.4.1 Setting Board Gain 13
- 4.4.2 Setting Channel Gain 14
- 4.5 Attenuation 14
- IN CONFIG 15
- 4.7.1 Single-Ended Inputs 16
- 4.7.2 Floating Differential 16
- 4.7.3 Fully Differential 16
- - THERMOCOUPLE LEAD 20
- + THERMOCOUPLE LEAD 20
- 5.5 Setting the Gain 22
- 5.5.1 Setting the Board Gain 22
- Output Gain Switch 22
- Channel Gain Switches 23
- 6.1 Channel Selection 24
- 6.2 VEXC JUMPER Select 24
- 6.3 CJC Jumper Selection 24
- 6.4 Powering the CIO-EXP-GP 24
- 6.6 Setting the Gain 26
- 6.6.1 Setting the Board Gain 26
- 6.8.1 Two-Wire RTD Hookup 28
- 6.8.2 Three-Wire RTD Hookup 28
- 6.8.3 Four-Wire RTD Hookup 28
- +5V Excitation Voltage Source 31
- 7.6 Setting the Gain 32
- 7.6.1 Setting the Board Gain 33
- A Half Bridge Example 38
- Half Bridge Calculations 38
- 8 SPECIFICATIONS 40
- 9 APPENDIX 42
- For your notes 44
- EC Declaration of Conformity 45
Verwandte Produkte und Handbücher für Hardware Measurement-computing CIO-EXP-GP
(32 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.036 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern