Measurement-computing USB-SSR08 Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Hardware Measurement-computing USB-SSR08 herunter. Measurement Computing USB-SSR08 User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken

Inhaltsverzeichnis

Seite 2 - USB-SSR08

Chapter 2 Installing the USB-SSR08 What comes with your USB-SSR08 shipment? As you unpack your USB-SSR08, make sure that the following components are

Seite 3 - HM USB-SSR08.doc

USB-SSR08 User's Guide Installing the USB-SSR08 Unpacking the USB-SSR08 As with any electronic device, you should take care while handling to av

Seite 4 - Table of Contents

USB-SSR08 User's Guide Installing the USB-SSR08 Remove from the enclosure to access the on-board switches To change the configuration of a switc

Seite 5

USB-SSR08 User's Guide Installing the USB-SSR08 Connecting the external power supply Power to the USB-SSR08 is provided with the 9 V, 1 A extern

Seite 6 - About this User's Guide

USB-SSR08 User's Guide Installing the USB-SSR08 If your system does not detect the USB-SSR08 If a "USB device not recognized" message

Seite 7 - Introducing the USB-SSR08

Chapter 3 Functional Details Internal components The USB-SSR08 has the following internal components, as shown in Figure 3-1.  Two (2) USB connecto

Seite 8 - Software features

USB-SSR08 User's Guide Functional Details External power connectors The USB-SSR08 has two external power connectors labeled POWER IN and POWER O

Seite 9

USB-SSR08 User's Guide Functional Details Control logic polarity switch (S2) Switch S2 is a four-position switch that sets the control logic pol

Seite 10 - Installing the USB-SSR08

USB-SSR08 User's Guide Functional Details LED states Independent LEDs (D1 – D8) at each module position indicate the on/off status of each modul

Seite 11 - Installing the software

Chapter 4 Specifications Typical for 25 °C unless otherwise specified. Specifications in italic text are guaranteed by design. I/O module configurat

Seite 12 - P/DNP/UP

USB-SSR08 USB-based 8 Solid-state Relay Module Interface Device User's Guide Document Revision 5, August, 2006 © Copyright 2006, Measurement C

Seite 13

USB-SSR08 User's Guide Specifications The USB-SSR08 monitors the external +9 V power supply voltage with a voltage supervisory circuit. If this

Seite 14 - POWER IN connector

USB-SSR08 User's Guide Specifications Humidity 0 to 90% non-condensing Main connector Table 9. Connector specifications Connector type Screw

Seite 15 - Functional Details

Declaration of Conformity Manufacturer: Measurement Computing Corporation Address: 10 Commerce Way Suite 1008 Norton, MA 02766 USA Measurement

Seite 16 - PWR LED

Measurement Computing Corporation 10 Commerce Way Suite 1008 Norton, Massachusetts 02766 (508) 946-5100 Fax: (508) 946-9500 E-mail: [email protected]

Seite 17 - Screw terminals

iii HM USB-SSR08.doc Your new Measurement Computing product comes with a fantastic extra — Management committed to your satisfaction! Thank you for ch

Seite 18 - LED states

Table of Contents Preface About this User's Guide ...

Seite 19 - Specifications

USB-SSR08 User's Guide Main connector...

Seite 20 - Environmental

Preface About this User's Guide What you will learn from this user's guide This user's guide explains how to install, configure, and u

Seite 21 - Main connector

Chapter 1 Introducing the USB-SSR08 Overview: USB-SSR08 features This user's guide contains all of the information you need to connect the USB-S

Seite 22 - Declaration of Conformity

USB-SSR08 User's Guide Introducing the USB-SSR08 Compatible SSR modules The USB-SSR08 board has locations for eight solid state relay modules th

Seite 23

USB-SSR08 User's Guide Introducing the USB-SSR08 Connecting a USB-SSR08 to your computer is easy Installing a data acquisition device has never

Verwandte Modelle: USB-SSR24

Kommentare zu diesen Handbüchern

Keine Kommentare