Measurement-computing StrainBook/616 Bedienungsanleitung Seite 130
- Seite / 146
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
12-2 Specifications 939294 StrainBook/616 User’s Manual
Triggering
Multi-Channel Analog Trigger (up to 64 channels):
Range: Selectable per channel to input range
Latency: 2 µs/channel, plus 4 µs maximum
TTL Trigger
Input Signa
l Range: 0 to 5V
Input Characteristics: T
TL-compatible with 10K Ohm pull-up resistor
La
tency: 300 ns
Software Trigger
Latency:
100 µs typical
External Clock
Connector: Available on DB25 digital input
Input Signal Range: 5V T
TL compatible
Input Characteristics: 50K Ohms pull up (to +
5V) in parallel with 50 pF
Input Protection: Z
ener clamped -0.7 to +5V
Delay: 200 ns
Signal Slew Rate Requirement: 20V/µs minimum
Rate:
Up to 1 MHz
Divisor Ratio: Divide by
1 through 255, selectable
Clock Counter Accuracy: <0.02%
Clock Counter Range: 0.01Hz to 100KHz
External Sync Ports
Number of External Sync Ports: 2, on rear panel
Maximum Number of Units to be Synchronized: 4 units, scan-synchronous (post trigger)
Maximum Length of Sync Cables: 15 feet (4.57 m), total for all cables
Sequencer
Operation: Programmable for channel, gain, and for unipolar/bipolar range in random order
Depth: 128 location
Channel-to-Channel Rate: 1 µs to 1.1 µs/channel, all channels equal
Maximum Repeat Rate: 1 MHz
Minimum Repeat Rate: 100 seconds per scan
Expansion Channel Sample Rate: Same as on-board channels, 1 to 1.1 µs, fixed
High-Speed Digital Inputs/General-Purpose Outputs
Connector: DB25 Female
Configuration: 16 TTL-compatible pins, selectable for input or output
Input Characteristics: T
TL-compatible
Output Characteristics: ALS T
TL output in series with 33 Ohms
Output Updates: Outputs may
be changed via program control
Input/Output Protection: Diode clamped to ground and +
5V
Period Counter
Operation: Internal counter calculates and reports the external clock’s period; counter can be read with each scan
Clock Counter Accuracy: <0.02% error
Clock Counter Range: 0.01 Hz to 100 kHz
Note: Specifications are subject to change w
ithout notice.
- StrainBook/616 1
- 489-0901 4
- 1086-0926 4
- 489-0902 4
- 1008-0901 4
- Table of Contents 7
- Chapter 7 – Triggers 8
- 967594 ix 9
- 967594 StrainBook/616 10
- Introduction 1 11
- What is StrainBook/616? 11
- 929494 StrainBook/616 12
- What Are WBKs? 13
- Operation Reference 2 15
- Basic Operation 16
- Channel Selection 17
- 967794 StrainBook/616 18
- A/D input source 19
- Triggers 21
- PDF NOTE: 22
- SYNC Notes: 23
- Programmable Features 24
- Operational Tips 24
- CH1 through CH8 27
- Status LEDS 27
- Associated Cables 30
- Software 4 31
- An Introduction to Software 32
- # Item Description 33
- 967594 Software 4-5 35
- 967594 Software 4-7 37
- Sensor Calibration 38
- 967594 Software 4-9 39
- Sensor Configuration Window 41
- Column Description 42
- Column Display Description 43
- (Units) 44
- 2 Point Manual Calibration 45
- 2 Point Auto Calibration 45
- Name Plate Calibration 48
- 967594 Software 4-19 49
- System Requirements 51
- Software Installation 52
- Install the Software 54
- How to make the connection: 57
- For DEDICATED Networks 62
- Bridge Configurations 6 65
- Introduction 65
- Bridge Applications 67
- Removing the Cover Plate 68
- Excitation Connection 69
- Installing a CN-115 70
- Configuration Diagrams 72
- B,D, or F Shunt 73
- CA-177 Strain-Gage Cable 76
- CN-189, DB9 Adapter Option 77
- Purpose of the WBK16/LC 79
- Caveats 82
- Installing a WBK16/LC 83
- Calibration Using WaveView 84
- Installing a CN-115-1 85
- Configuring a CN-115-1 86
- Digital (TTL) Trigger 89
- Triggers 7 89
- Multi-Channel Trigger 90
- Above-Level Trigger 91
- Below-Level Trigger 91
- Rising-Edge Trigger 92
- Falling-Edge Trigger 92
- Trigger Latency & Jitter 93
- Digital-Pattern Trigger 94
- Note: The Clock Divider 95
- 977694 StrainBook/616 96
- Connections for 16-Bit Mode 97
- Connections for 8-Bit Mode 98
- TTL Trigger 99
- External Clock 99
- 977794 StrainBook/616 100
- Overview 101
- CE Standards and Directives 101
- Safety Conditions 102
- Dust Cap 103
- Shielded 103
- BNC Connector 103
- Noise Considerations 104
- System Expansion 10 105
- Channel Expansion 106
- DIN 5 Power Pinout* 107
- CA-242 or 107
- CA-242-7 107
- 3.3 Amp limit 111
- @ 15 VDC * 111
- CA-74-1 (1 ft.) or 112
- CA-74-5 (5 ft.) 112
- CAUTION 113
- Product Care 115
- Driver Support 116
- Troubleshooting Tables 116
- Channel readings are wrong 118
- WaveView Scope stops 119
- Ethernet Problems 122
- WaveView Issues 124
- Frequently Asked Questions 125
- (4) Topic: Sampling Rates 126
- (5) Topic: Calibration 126
- Customer Support 127
- StrainBook/616 12 129
- Expansion Options 131
- Quick Guide 133
- 977194 Appendix A 134
- Before you run a test 139
- 977194 Appendix B 140
- Glossary 143
- 969597 Data Acquisition 144
Verwandte Produkte und Handbücher für Hardware Measurement-computing StrainBook/616
(6 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern