Measurement-computing Personal Daq rev.6.0 Bedienungsanleitung Seite 88
- Seite / 170
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
10 Update Digital Outputs Updates the digital output channels. This item is only enabled when the digital
output channels are not updated and the acquisition state is idle.
11 Save Power-up Settings Saves the current power-up settings for all devices in the configuration. The
power-up settings take effect when the device is first plugged into an active USB
port.
12 Chart Display Opens the Chart Display, where data is displayed in graphical in a chart format. If
Chart Display is already open, selecting this item gives the window focus.
13 Bar Graph Meters Display Opens the Bar Graph Meters, where data is displayed in a bar graph format. If Bar
Graph Meters is already open, selecting this item gives the window focus.
14 Analog Meters Display Opens the Analog Meters Display, where data is displayed in an analog meter
format. If Analog Meters Display is already open, selecting this item gives the
window focus.
15 Digital Meters Display Opens the Digital Meters Display, where data is displayed in a digital meter format.
If Digital Meters is already open, selecting this item gives the window focus.
16 Use Data Destination Turns the Use Data Destination feature on or off.
17 Set Data Destination Cell Sets the data destination cell to the “active” cell in the current workbook.
18 Use Data Header Turns the Use Data Header feature on or off.
19 Options… Opens Personal DaqViewXL’s Options Dialog.
20 Preferences… Opens Personal DaqViewXL’s Preferences Dialog. From this dialog box you can
use the General and Measurement Units dialog boxes as described below.
General − Allows you to select “untitled” or “pDaq”
configurations for the default filename used by
Personal Daq. Note that Personal DaqView automatically
loads the last saved configuration file. The lower portion of
the General screen pertains to configuration file settings.
Measurement Units − Allows you to set the desired default
units for the Channel Configuration Window’s spreadsheet.
Note that scale and offset automatically reset to a pre-
designated default according to the unit selected.
Changing the measurement unit defaults does not
immediately affect the Channel Configuration Window’s
spreadsheet columns. For example: If you set your voltage
default to µV, but the channels are set with V units, they will
retain the V units. However, changing these channels to
temperature, then back to voltage would result in the default
units (µV) and the associated scale & offset. The new
default units are also applied to all channels when a new
configuration file is created.
Preferences Screen Captures (Condensed Images)
21 About… Provides version information for the active Personal DaqViewXL add-in and the
Personal DaqView application.
22 Help… Launches the Personal DaqViewXL section of the Personal DaqView help file.
6 491-0905, rev 3.0 918596 Personal DaqViewXL User’s Guide
- User’s Manual 1
- Personal Daq 1
- 491-0901 4
- 1086-0926 4
- 1086-0922 4
- About This Manual 5
- Table of Contents 7
- 5 – Signal Management 8
- 6 - Calibration 8
- Unit Startup 1 9
- Install Software 10
- Install Hardware 10
- Personal Daq User’s Manual 11
- Unit Startup 1-3 11
- 1-4 Unit Startup 12
- Personal Daq User’s Manual 12
- CAUTION 13
- Start Personal DaqView 15
- Configure System 16
- Channel Configuration 17
- Acquisition Configuration 17
- Collect Data 18
- PDAQ.BIN, is as follows: 19
- No Expansion 21
- ---- N/A ---- ---- N/A 21
- Features 22
- Theory of Operation 23
- Optical Isolation 24
- A/D Conversion 24
- Input Ranges 24
- Analog Input Configuration 25
- Automatic Calibration 27
- Thermocouple Measurements 27
- Analog Specifications 30
- Input Voltage Ranges 30
- Thermocouple Accuracy 31
- General Specifications 32
- Optional Accessories 32
- Channel Connection Layouts 33
- Calibration 35
- Hardware Setup 3 37
- PDQ Expansion Modules 38
- USB Hubs and Power Adapters 39
- 3-4 Hardware Setup 40
- Hardware Setup 3-5 41
- 3-6 Hardware Setup 42
- Main Control Window 45
- Pull-Down Menus 46
- Measurement Units 47
- Channel Configuration Window 48
- Common Spreadsheet Columns 49
- (b) for the application in 50
- cell for PD1_A01, typed 51
- Analog Input Spreadsheet 52
- Measurement Duration Column 53
- Resolution and Settling Time 55
- 4-14 Personal DaqView 56
- The Trigger Section 58
- Averaging 58
- Acquisition Parameters 59
- 4-18 Personal DaqView 60
- Why use Auto Rearm? 61
- Disabling Auto Rearm 61
- Meter Toolbars 62
- Meter Pull-Down Menus 63
- Meters Configuration Menu 63
- Configuring a Meter 64
- Bar Graph Meters 66
- Analog Meters 67
- Digital Meters 68
- Chart Display 69
- Toolbar Items 71
- Item Description 72
- 4-34 Personal DaqView 76
- 4-36 Personal DaqView 78
- Chart Setup Wizard 79
- 4-40 Personal DaqView 82
- System Requirements 84
- Installation 84
- First Time Use 84
- Configuration Reference 87
- Auto-Load Function 90
- Real-Time Charting 93
- Data Header 94
- Hints and Tips 95
- Signal Acquisition 100
- Triggering 101
- Signal Modes 102
- System Noise 103
- Input and Source Impedance 104
- Crosstalk 104
- Analog Filtering 104
- Introduction 105
- Required Equipment 106
- Calibration Procedure 106
- 878395 Calibration 6-3 107
- 878395 Calibration 6-5 109
- Radio Frequency Interference 111
- Troubleshooting 112
- Customer Assistance 115
- Appendices 117
- Overview 119
- Data Acquisition Environment 119
- Programming Models 120
- Read 1 sample from multiple 122
- Buffers 125
- Multiple Channel Types 128
- API Commands B 133
- (Does not apply to 161
- Personal Daq/54) 161
- Note: Includes “NE” version 163
- Table 9. API Error Codes 165
- 83h - 131 166
Verwandte Produkte und Handbücher für Hardware Measurement-computing Personal Daq rev.6.0
(26 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern