Measurement-computing BTH-1208LS-OEM Bedienungsanleitung

BTH-1208LS-OEM Wireless Multifunction DAQ Device Document Revision 5 December 2014 © Copyright 2014 User's Guide

10 Chapter 3 Functional Details Analog input acquisition modes The BTH-1208LS-OEM can acquire analog input data in three different modes – software p

BTH-1208LS-OEM User's Guide Functional Details 11 In both Bluetooth mode and USB mode, you can start a hardware-paced scan with either a softwar

BTH-1208LS-OEM User's Guide Functional Details 12 Power/pairing button The power/pairing button has different functions depending on the power s

BTH-1208LS-OEM User's Guide Functional Details 13 Connector J1 Header connector J1 provides connections for the analog inputs, analog outputs, a

BTH-1208LS-OEM User's Guide Functional Details 14 Signal connections Analog input You can connect up to eight single-ended analog input connecti

BTH-1208LS-OEM User's Guide Functional Details 15 Carefully match the gain to the expected voltage range on the associated channel or an over ra

BTH-1208LS-OEM User's Guide Functional Details 16 Figure 4. Digital I/O external resistor configuration Bulkhead signals The function of the bu

BTH-1208LS-OEM User's Guide Functional Details 17 Ground The analog ground (AGND) pin on connector J1 provide a common ground for all analog cha

Chapter 4 Specifications All specifications are subject to change without notice. Typical for 25°C unless otherwise specified. Specifications in ita

BTH-1208LS-OEM User's Guide Specifications 19 Note 1: Input current is a function of applied voltage on the analog input channels. For a given

HM BTH-1208LS-OEM Your new Measurement Computing product comes with a fantastic extra — Management committed to your satisfaction! Thank you for choo

BTH-1208LS-OEM User's Guide Specifications 20 Noise performance Table 6. Noise performance, differential mode Range Typical counts LSBrms ±20

BTH-1208LS-OEM User's Guide Specifications 21 Digital input/output Table 11. Digital I/O specifications Parameter Specification Digital type

BTH-1208LS-OEM User's Guide Specifications 22 External trigger Table 12. Digital trigger specifications Parameter Specification Trigger source

BTH-1208LS-OEM User's Guide Specifications 23 Counter Table 14. Counter specifications Parameter Specification Pin name CTR Counter type Even

BTH-1208LS-OEM User's Guide Specifications 24 Power Table 17. Power specifications Parameter Condition Specification Supply current, USB sour

BTH-1208LS-OEM User's Guide Specifications 25 Mechanical Table 21. Mechanical specifications Parameter Specification Dimensions (L × W × H) 99

BTH-1208LS-OEM User's Guide Specifications 26 Bulkhead signals (J3) Table 26. Bulkhead signals Pin Signal name Pin description Pin Signal na

Measurement Computing Corporation 10 Commerce Way Suite 1008 Norton, Massachusetts 02766 (508) 946-5100 Fax: (508) 946-9500 E-mail: [email protected]

3 Table of Contents Preface About this User's Guide ...

BTH-1208LS-OEM User's Guide 4 Counter ...

5 Preface About this User's Guide What you will learn from this user's guide This user's guide describes the Measurement Computing BTH

6 Chapter 1 Introducing the BTH-1208LS-OEM The BTH-1208LS-OEM is a multifunction data acquisition device that communicates using Bluetooth® wireless

BTH-1208LS-OEM User's Guide Introducing the BTH-1208LS-OEM 7 Functional block diagram BTH-1208LS-OEM functions are illustrated in the block diag

8 Chapter 2 Installing a BTH-1208LS-OEM Unpacking As with any electronic device, you should take care while handling to avoid damage from static elec

BTH-1208LS-OEM User's Guide Installing a BTH-1208LS-OEM 9 5. Press and hold the power/pairing button for two seconds to remove the device from